PLUMBING BASICS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Basics: A Prerequisite for Installing a Bathtub

Plumbing Basics: A Prerequisite for Installing a Bathtub

Blog Article

More Details

This post following next involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is pretty much compelling. Don't miss it.


How to Install a Bathtub
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult task. If the old bathtub is easily easily accessible, the job can move immediately; if you have to open a wall surface to get rid of the old tub and also place the new tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified yourself for the job as well as are comfortable trying it. Instead of working with a contractor to take over a halfway-completed project, it is better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you install a brand-new tub in your shower room if you have already acquired a brand-new tub and do not need to alter the setup of your previous water pipes.
Your tools and material checklist must make up the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installment


    First of all, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
    Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.

    Removing Old Taps


    If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is frequently the case.
    Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
    Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Making use of both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
    The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bath tub till the level reviews degree.
    To mount faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
    Activate the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and additionally examine the overflow outlet and the typical outlet for leakages.
    Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has actually been made use of at the very least once as this will resolve it right into its final placement.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
    If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in area between the tap and also the sink. Secure the tap in position with the supplier offered backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The previous kind should be linked to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the area where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, triggering the water to permeate the wall surface between the bathroom as well as the tiling, causing complications with dampness and also feasible leakages to the ceiling below.
    You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not think about this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is a good idea to fit the tiles using waterproof or water-proof glue and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I found that blog entry on Installing A Bathtub when doing research the internet. Enjoyed our post? Please share it. Help others discover it. Thanks so much for your time spent reading it.


    Dial, we deliver!

    Report this page